Menu
This article will explain how to use your TP-Link N router as an access point. The main router will be connected to the TP-Link N router via LAN port (as seen below). The WAN port is not used for this configuration. Main Router Access Point Step 1 Connect your computer to a second LAN port on your TP-Link N router using an Ethernet cable. Login to the TP-Link web interface through the IP address listed on the label on the bottom of your TP-Link N router (see below link for assistance): Note: Though possible, it is not recommended to attempt this process over Wi-Fi Step 2 Go to NetworkLAN on the side menu and change the LAN IP address of your TP-Link N router to an IP address on the same segment of the main router.
This IP address should be outside the main router’s DHCP range. Example: if the DHCP of your main router is 192.168.2.100 – 192.168.2.199 then you can set the IP of the TP-Link N router to 192.168.2.X (X should be outside your main router's DHCP range), like 192.168.2.11.
Note: After changing the LAN IP address a reboot will be required and you will need to log into the TP-Link N router with the new IP address. Step 3 Go to Wireless Wireless Settings and configure the SSID (Network name)which can be the same or different from the main router’s. Step 4 Go to Wireless Wireless Security and configure the wireless security. WPA/WPA2-Persona lis recommended as the most secure option.
Once configured, click Save. Note: If using a dual band router, repeat this process for the 5GHz band as well. Step 5 Go to DHCP DHCP Settings and select Disable the DHCP Server. Step 6 Go to System Tools Reboot and select Reboot to reboot the device.
Step 7 Use an Ethernet cable to connect the main router to your TP-Link N router through their LAN ports (any LAN ports may be used). All other LAN ports on your TP-Link N router will now grant devices Internet access.
Alternatively, any Wi-Fi device can now access the Internet through your TP-Link N router by using the SSID and Password set up in the above steps.
Cara setting TL-MR3220 wirelees N router adalah salah satu Router buatan TP-LINK yang memiliki segudang fitur dan fungsi, diantaranya adalah dapat dijadikan sebagai router yang menyalurkan koneksi internet dari modem baik modem 3G, modem 4G, modem EVDO CDMA maupun modem adsl dan juga modem lainnya ke perangkat komputer, smarphone dan juga peangkat jaringan komputer lainnya. Jika kita mmeiliki sembuah modem USB baik 3G atau 4G dan ingin agar koneksi internet dari modem USB dapat digunakan secara bersamaan hingga beberapa alat lainnya maka dapat memanfaatkan router 3G/4G TP-LINK TL-MR3220 ini. Router ini adalah salah satu Wireless Router untuk sharing koneksi modem 3G HSDPA atau EVDO dengan konfigurasi yang sangat mudah. Transfer Rate data dapat mencapai hingga 150Mbps, dan Jika ingin kcepatan tansfer data yang lebih cepat hingga 300Mbps maka dapat menggunakan versi diatasnya yaitu TL-MR3420.
Router ini mendukung mode AP Router, Bridge dan juga mode WDS. TX Power TL-MR3220 maksimal hingga 100mW (20dBm) sehingga jangkauannya cukup luas serta mampu menembus tembok dirumah atau kantor. Bagusnya lagi pada router ini juga disediakan fitur Bandwith Management untuk pengaturan besar aliran data yang ditasfer, dan juga mmeiliki fitur parental kontrol.
Router 3G dan 4G TP-Link tl-mr3220 Fitur dan Spesifikasi TL-MR3220 wireless N router 3G/4G Router TL-MR3220 bisa digunakan untuk sharing koneksi internet melalui jalur kabel LAN dan juga melalui jalur Wi-fi tanpa kabel sehingga tidak ribet pengaplikasiannya. Router ini memiliki port wan 1 buah plus 4 buah port LAN untuk mengkoneksikan hingga 4 komputer sekaligus dengan 4 buah kabel LAN. Yang cukup menarik router ini telah dibekali dengan berbagai fasilitas pengaturan koneksi seperti MAC-filtering yang sangat berguna untuk menyaring perangkat yang terkoneksi dengan router secara privat dan lebih aman, bahkan jumlah modem 3G atau modem 4G yang didukung oleh router TL-MR3220 juga sangat banyak yang terdiri dari beberapa seri dan merk modem terkenal.
Berikut fitur yang dimiliki router TP-LINK TL-MR 3220v2. Mendukung dengan berbagai modem USB UMTS/HSPA/EVDO dan telah teruji. Ada tambahan fitur bandwidth control, yang memungkinkan pengaturan serta pembatasan aliran bandwidth untuk setiap PC atau perangkat lain yang terkoneksi. Memiliki fitur failover yang dapat memastikan koneksi 3G/WAN internet selalu terkoneksi dengan baik. Kecepatan transfer Wireless LAN maximal hingga 150Mbps, sangat mendukung kecepatan streaming video HD dan game online. Dilengkapi dengan sistem Keamanan wireless enkripsi yang dapat diatur hanya dengan mengakses satu tombol QSS (Easy one-touch).
Como endosar vale vista chile. Frm Part 1 Schweser Download Games Endosar Un Vale Vista Chile El Caliz Y La Espada Pdf El Arte De La Cocina Francesa Pdf Euro Truck Simulator 2. Mar 22, 2018 - Consulta, que precauciones se deben tener al recibir un vale vista, me refiero a que no sea mula o estafa o cualquier problema que se pueda. Sep 21, 2017 - Moonlight Amphitheater Vista. The Vista Press - Vista & North County News The Vista Press. By Editor 8 hours ago. Endoso Vale Vista Chile.
Spesifikasi TP-LINK TL-MR 3220 HARDWARE FEATURES. Button: WPS/Reset Button Wireless On/Off Switch.
Power On/Off Button. Antenna Type: Omni directional, Detachable, Reverse SMA. Antenna Gain: 5dBi. Interface: USB 2.0 Port for LTE/HSUPA/HSDPA/UMTS/EVDO USB Modem 1 10/100Mbps WAN Port, 4 10/100Mbps LAN Ports, support the auto-Negotiation and auto-MDI/MDIX. External Power Supply: 9VDC/0.85A. Dimensions ( W x D x H ): 8.5.4.1.7 in. WIRELESS FEATURES.
EIRP: Nyalakan komputer atau pc dan juga nyalakan router 3G/4G TL-MR3220 - Kita kali ini menggunakan modem smartfren – maka pasang modem USB anda pada Router - Pasang kabel LAN pada port LAN nomer 1 hingga nomer 4 bisa semua bawaan router TL-MR3220 - Pasang kabel LAN ujung lainnya pada port LAN di Laptop atau komputer anda - Setting IP Adress automatic di komputer atau laptop - Buka browser mozilla dan ketik pada alamat IP 192.168.0.1 dan tekan tombol Enter, Password “admin” dan user juga isikan “admin”, lalu tekan enter dan akan keluar tampilan sebagai berikut. Langkah selanjutnya pilih pada menu Quick Setup dan sebelah kanan klik Next maka akan keluar lagi pilihan sebagai berikut:. 3G/4G Only (Recommended) Juka hanya menggunakan Modem USB maka sebaiknay pilih yang pertama ini. 3G/4G Preferred. WAN Preferred. WAN Only - Lanjutkan dengan klik tombol Next dan akan keluar jendela selanjutnya maka silahkan pilih operator selule yang anda gunakan, beberapa operator telah ada dalam daftar dan tinggal pilih salah satu kemudian lanjutkan kembali dengan pilih Next.
Maka kita akan mendapatkan tampilan berikutnya sbagai langkah setting terakhir yaitu untuk melakkan perubahan nama wifi yang akan kita gunakan, lihat gambar keterangan dibawah ini. Keterangan: cukup biarkan parameter lainnya dan silahkan rubah yang perlu saja seperti Wireless Natwork Name: “isi dengan nama pilihan anda” - kemudian keamanan, disini agar lebih mudah kita akan menggunakan jenis WPA-Personal/WPA2-Personal - Pada kolom Password isikan password baru yang diinginkan (minimal terdiri dari 8 karakter) terserah anda.
Terakhir pilih Next - dan akan ada pilihan untuk Reboot, klik tombol Reboot dan tunggu router anda akan kembali menyala dalam beberapa detik dengan setingan yang baru anda buat tadi. Mudah dan simpel. Dan untuk settingan lainnya seperti Wireless MAC Filtering, Parental Control Settings, Bandwidth Control Settings, maka dapat diekplorasi sendiri tanpa harus takut salah. Namun untuk pengaturan fitur Firmware Upgrade yang terdapat pada menu system tools maka sebaiknya dtinggalkan dulu sebelum memiliki tutorial yang jelas tentang itu. Atau tungu totorial lainnya dari kamu tentang router TP-LINK TL-MR3220 ini pada kesempatan berikutnya. Semoga ulasan ini bermanfaat dan jangan lupa untuk mambaca juga ulasan lainnya tentang.
The TL-WR1043 router from Chinese manufacturer TP-Link is one of the most capable AND inexpensive routers on the market today. With four Gigabit Ethernet LAN ports, Wireless-N, and a cost of only $54 (at the time of this writing), you cannot find a better value. And it efficiently solves a problem many people have: insufficient wireless coverage. If your home is large or prone to Wi-Fi “dead spots” where the signal is weak, you can use a wireless bridge to help overcome these problems.
A bridge does exactly what it sounds like: it connects two Wi-Fi networks without the need for cabling. The bridge is nothing more than a second router that joins to your existing network, and extends its range. A bridge also increases the number of wired devices you can connect to your home network via the wired Ethernet ports on the back of it.
Anything you connect there is also connected to your home network, enabling you to connect devices without onboard Wi-Fi, such as DVD players or game consoles. To do this, you need two routers, a laptop, and an Ethernet cable. This article assumes one of those two routers is already setup and functioning as your primary Wi-Fi router, and the other is out-of-the-box, unconfigured TP-Link TL-WR1043 router. It will be referred to as the “bridge router” in this article. It is also recommended that you update the router to the latest firmware version from TP-Link before proceeding (3.13.4 Build 110429 Rel.36959n as of this writing) Here is how you build the bridge: 1) Write down your existing wireless settings Open up the web-based management console on your existing, primary router. Browse to the Wireless/Wireless Settings section and write down the values for channel, SSID, transmission mode, and the wireless security method and password in use.
You will need these value later when you configure the bridge router. 2) Connect the bridge router Connect the bridge router directly to your laptop with an ethernet cable plugged into any of its four LAN ports. Disable the laptop’s wifi connection, which will ensure your laptop is only talking only to the router. Power the router on, and your laptop should obtain an IP address from it. 3) Open the Administration console Open a web browser and go to the bridge router’s administration page at 192.168.1.1; you will be prompted for the default password of admin/admin 4) Select the Wireless/Wireless Settings section. In this section, set a different Wireless Network Name (SSID) from the one used by your primary router.
Then set all of the other settings on this page to match your primary router. After making these changes, you will be prompted to reboot the router, which you must do to ensure these changes take effect. After the reboot, move on to the next step.
Router Wifi Philippines
5) Give the bridge router a different IP. Open the router management console once again, and select the Network/LAN section. In this section, you will see that the router has a default IP address of 192.168.1.1, which is the same IP address as your primary router. In order to avoid an IP address conflict, change the IP address of the bridge router to 192.168.1.2.
You will need to reboot the router after making this change. 6) Setup the bridge In the router management console, browse again to the Wireless/Wireless Settings section. This time, tick the checkbox entitled “Enable WDS Bridging.” This will open a drop-down section with a number of new settings. You will need to fill in the “SSID(to be bridged”) and the “BSSID(to be bridged)” sections. The fastest way to do this is click the “Survey” button. This will open a new window called “AP List” which shows you all the Wi-Fi networks in range. Look for your primary router in the list by its name (SSID), and click the “Connect” link on the right.
You will notice that the SSID and BSSID sections are now filled out properly. Now simply enter the wireless security values you copied from your primary router. It should look something like this, with the sections with red arrows filled in. Save the settings, and your router will reboot and join your existing Wi-Fi network. 7) Disable DHCP Since your primary router will be handing out IP addresses on your network, you do not want the bridged router also trying to assume this role. Select the DHCP/DHCP Settings section, and disable the DHCP server. Then choose the System Tools/Reboot section, and reboot the router for the last time.
8) Reconnect to your primary router. Disconnect the Ethernet cable from the bridge router and reenable your Wi-Fi. You should now see two possible SSID’s for you to connect to: the primary router and the new bridge router. Connect to the primary router, as you would normally do. 9) Validate the bridge setup. You can perform a few tests to ensure your setup is configured correctly: a) Browse to the administration page on the primary router.
Tp Link Wr941nd Firmware
Select the Wireless/Wireless Statistics section. In this section, you should see the MAC Address of your bridge router, and some values in the Received and Sent Packets counters, indicating the connection is working. It should look like this: Note that the MAC address of your bridge router should be printed on the bottom of the device. B) Browse to the 192.168.1.2 address, which is the management console of the bridge router. You should be able to resolve this address and login to the adminstration page on the bridge router without issue. If both of these test pass, you should be reasonably certain your bridge is configured correctly and running.
10) Connect to the bridge Now reset your Wi-Fi connection to the SSID of the bridge router. You should be able to connect successfully, get an IP address through the primary router, and be able to connect to the Internet. You should also be able to connect a wired device to any of the LAN ports on the router and get to the Internet as well.
TP-Link TL-WR941ND Login Instructions This page shows you how to login to the TP-Link TL-WR941ND router. Other TP-Link TL-WR941ND Guides. Find Your TP-Link TL-WR941ND Router IP Address We need to know the Internal IP Address of your TP-Link TL-WR941ND router before we can login to it. TP-Link TL-WR941ND IP Addresses 192.168.0.1 If you did not see your router's ip address in the list above. There are 2 additional ways that you can determine your router's IP address:. You can either follow our How To Find Your Routers IP Address guide.
Or you can use our free software called Router IP Address. Now that you have your router's Internal IP Address we are ready to login to it. Login to the TP-Link TL-WR941ND Router The TP-Link TL-WR941ND has a web interface for configuration. You can use any web browser you like to login to the TP-Link TL-WR941ND. In this example we'll use Internet Explorer. Enter TP-Link TL-WR941ND Internal IP Address Put the Internal IP Address of your TP-Link TL-WR941ND in the Address Bar of your web browser. It looks like this: Then press the Enter key on your keyboard.
You should see a dialog box pop up asking your for your TP-Link TL-WR941ND username and password. TP-Link TL-WR941ND Default Username and Password You need to know the username and password to login to your TP-Link TL-WR941ND. All of the default usernames and passwords for the TP-Link TL-WR941ND are listed below. TP-Link TL-WR941ND Usernames TP-Link TL-WR941ND Passwords admin admin Enter your username and password in the dialog box that pops up. It looks like this: TP-Link TL-WR941ND Home Screen You should now see the TP-Link TL-WR941ND Home Screen, which looks like this.
If you see this screen, then congratulations, you are now logged in to your TP-Link TL-WR941ND. You are now ready to follow one of our other guides. Solutions To TP-Link TL-WR941ND Login Problems If you can not get logged in to your router, here a few possible solutions you can try. TP-Link TL-WR941ND Password Doesn't Work You should try other TP-Link passwords. We have a large list of TP-Link Passwords that you can try.
Perhaps your router's default password is different than what we have listed here. Forgot Password to TP-Link TL-WR941ND Router If your Internet Service Provider supplied you with your router then you might want to try giving them a call and see if they either know what your router's username and password are, or maybe they can reset it for you. How to Reset the TP-Link TL-WR941ND Router To Default Settings If you still can not get logged in then you are probably going to have to reset your router to its default settings. You may want to follow our guide called.
Other TP-Link TL-WR941ND Guides Here are some of our other TP-Link TL-WR941ND info that you might be interested in.